Estoy trabajando con Docker y estoy usando ros-melodic-mavros y ros-melodic-mavros-extras para controlar un drone iris PX4. en la versión 1.1 funcionó bien. Estoy controlando drones usando Positiontarget para el tema: '/ iris _ {} / mavros / setpoint_raw / local pero no sucede nada en 1.2. No hay opción para obtener una versión anterior de apt-get (¿por qué?)
Mavros: 1.2
ROS: melódico
Ubuntu: 18.04
estibador: 19.03.11
Cenador: 9
[] ArduPilot
[x] PX4
Versión: 1.10
header:
seq: 889
stamp:
secs: 1345
nsecs: 601000000
frame_id: ''
status:
-
level: 0
name: "iris_1/mavros: FCU connection"
message: "connected"
hardware_id: "udp://:14541<strong i="20">@localhost</strong>:14581"
values:
-
key: "Received packets:"
value: "27630"
-
key: "Dropped packets:"
value: "0"
-
key: "Buffer overruns:"
value: "0"
-
key: "Parse errors:"
value: "0"
-
key: "Rx sequence number:"
value: "238"
-
key: "Tx sequence number:"
value: "0"
-
key: "Rx total bytes:"
value: "24864594"
-
key: "Tx total bytes:"
value: "735053"
-
key: "Rx speed:"
value: "24529.000000"
-
key: "Tx speed:"
value: "742.000000"
-
level: 0
name: "iris_1/mavros: GPS"
message: "3D fix"
hardware_id: "udp://:14541<strong i="21">@localhost</strong>:14581"
values:
-
key: "Satellites visible"
value: "10"
-
key: "Fix type"
value: "3"
-
key: "EPH (m)"
value: "0.00"
-
key: "EPV (m)"
value: "0.00"
-
level: 0
name: "iris_1/mavros: Heartbeat"
message: "Normal"
hardware_id: "udp://:14541<strong i="22">@localhost</strong>:14581"
values:
-
key: "Heartbeats since startup"
value: "1016"
-
key: "Frequency (Hz)"
value: "0.951928"
-
key: "Vehicle type"
value: "Quadrotor"
-
key: "Autopilot type"
value: "PX4 Autopilot"
-
key: "Mode"
value: "OFFBOARD"
-
key: "System status"
value: "Active"
-
level: 2
name: "iris_1/mavros: System"
message: "Sensor health"
hardware_id: "udp://:14541<strong i="23">@localhost</strong>:14581"
values:
-
key: "Sensor present"
value: "0x1020002F"
-
key: "Sensor enabled"
value: "0x1021000F"
-
key: "Sensor health"
value: "0x1020002F"
-
key: "3D gyro"
value: "Ok"
-
key: "3D accelerometer"
value: "Ok"
-
key: "3D magnetometer"
value: "Ok"
-
key: "absolute pressure"
value: "Ok"
-
key: "rc receiver"
value: "Fail"
-
key: "AHRS subsystem health"
value: "Ok"
-
key: "CPU Load (%)"
value: "0.0"
-
key: "Drop rate (%)"
value: "0.0"
-
key: "Errors comm"
value: "0"
-
key: "Errors count #1"
value: "0"
-
key: "Errors count #2"
value: "0"
-
key: "Errors count #3"
value: "0"
-
key: "Errors count #4"
value: "0"
-
level: 0
name: "iris_1/mavros: Battery"
message: "Normal"
hardware_id: "udp://:14541<strong i="24">@localhost</strong>:14581"
values:
-
key: "Voltage"
value: "11.32"
-
key: "Current"
value: "-1.0"
-
key: "Remaining"
value: "51.0"
-
level: 0
name: "iris_1/mavros: Time Sync"
message: "Normal"
hardware_id: "udp://:14541<strong i="25">@localhost</strong>:14581"
values:
-
key: "Timesyncs since startup"
value: "10168"
-
key: "Frequency (Hz)"
value: "9.995240"
-
key: "Last RTT (ms)"
value: "0.000000"
-
key: "Mean RTT (ms)"
value: "0.117328"
-
key: "Last remote time (s)"
value: "1016.949000000"
-
key: "Estimated time offset (s)"
value: "328.622159175"
---
WARNING: mavros/target_system_id not set. Used default value: 1
WARNING: mavros/target_component_id not set. Used default value: 1
NOTE: Target parameters may be unset, but that may be result of incorrect --mavros-ns option.Double check results!
ERROR. I got 0 addresses, but not your target 1:1
---
Received 0 messages, from 0 addresses
sys:comp list of messages
rosrun mavros checkid --mavros-ns iris_1 / mavros
ERROR. I got 0 addresses, but not your target 2:1
---
Received 0 messages, from 0 addresses
sys:comp list of messages
Se están publicando puntos (comprobados con eco rostopic) pero el dron no se mueve en absoluto.
Estoy teniendo el mismo problema. Mi código funcionó en 1.1.0, después de ser forzado a actualizar a 1.2.0, todo se rompió. Ahora mi UAV tiene problemas con su giroscopio por alguna extraña razón.
Puede verificar 1.1.0 y compilarlo desde el código fuente. Pero creo que hay algo más porque setpoint_raw permanece igual durante años.